Jet Problems

Jet Problems Jet Problems Jet Problems

Jet problems

Some of the jets pop out

This applies only to snap-in jet inserts. Beginning with 2013, new spas use jet inserts that screw in and are unlikely to pop out

Some jet inserts are designed to rotate about a half a turn in order to turn on or off water flow. They are also designed to come out if you turn them past the attachment. When a jet insert is turned past its attachment point, it can be easily blown out of the jet body with water pressure. To prevent this, rotate the jet insert only as far as it will easily turn until it hits the stopping point.

A jet that keeps popping out may not be pushed in all the way. By pushing in on the jet insert, you should hear a click. This indicates that the insert is installed all the way into position. If there is no click, the jet is in the wrong way and will pop out.

Sometimes jet inserts weaken over time due to constant exposure to water and chemicals. If the jets are subjected to extreme chemicalconditions or abuse, they will weaken and fail.

If the jet insert is a replacement, if it is the wrong size or type for the jet body, it will not stay in place. Change the insert to the correct size or type. Many inserts look alike and have the same size face. The nozzle in the back is where the clips are located and is what has to match the jet body.

Some of the jets will not rotate

This applies only to jets that are designed to rotate to allow water pressure to be turned on or off. Some jets are fixed in place and are always on.

If you are in need of relpacements parts visits

Jets that are designed to rotate should do so easily. Tightness in jet rotation can be caused by age, chemical or calcium build-up, or improper insertion. If a rotatable jet does not turn, it may be stuck. Grip it firmly and rotate it counter-clockwise until it snaps and pops out of the jet body. Remove it and clean it thoroughly, then replace it in the jet body. It should rotate more easily after cleaning.

The jet insert will not spin

This refers to jets with a spinner in the center that work with water pressure and not to jet rotation, which refers to turning on or off water pressure.

Is the jet insert completely open?

Some jets are able to rotate in order to open or close them. Rotate the rim of the jet insert o turn the jet on.

Is there water pressure to the jet?

Listen for the sound of the motor. If the pump isn’t running, try pushing the JETS button on the control panel. If the pump that supplies water to the jets is on low speed, there won’t be enough water to operate the jets. Press the JETS button to activate the pump on high speed.

Check the water diverter valve. It may be diverting water away from the group of jets you want to use. Diverter valves direct water towards the jets to allow water flow to reach them. Experiment by turning the handle on the valves to see where the water goes.

Does the jet contain a spinning type jet insert?

Jet inserts come in many different shapes, sizes, and styles. Spinner jets usually have an internal component that spins or causes the water to spin. If the jet insert doesn’t have that component, the jet will produce water flow but not the spinning action that is usually associated with spinner jets. Change the jet insert to a spinner type of insert (if applicable) to achieve spinning action.

Is there intermittent spinning action?

If the spinner insert hangs up or spins slowly, it is probably due to debris in the spinner insert.

Remove the jet insert and clean the debris out of the spinning mechanism. Use a spray hose to spray out grit from inside the insert. If it still turns intermittently, the insert will have to be replaced.

Long hair or lint can also wind up around the shaft of the spinning insert and cause a slowdown in spinning action. Turn the insert shaft counter-clockwise to unwind hair and long debris. Replace insert if necessary.

Some jets are not as powerful as they used to be

This may indicate a problem with water pressure. Check water pressure troubleshooting on that page.

READ MORE AT CALSPASBLOG.COM


Everything You Need to Know About Keeping Your Spa Water Fresh

Do you want to protect your investment into your brand new spa? A couple simple steps on a set schedule can keep your investment lasting long, looking good, and keep you feeling relaxed with every use. The Basics (Routine Maintenance) There are a couple simple things to keep an eye on in order to keep your spa optimal for regular use. First off, the most important thing is to use your basic senses. Does your water look clear? Does it smell funny? Does the water feel clean? If you notice anything out of the ordinary about your water, you may need to stay on top of your routine maintenance for your spa. If you notice any leaves or large debris in your water, use a skimmer to scoop up anything you can see. If you notice any smells or scale floating in the water, continue in the article to find out how to remedy these issues. A good thing to regularly check is water chemistry. This is one of the most important things to keep track of when maintaining your spa. A couple test strips or pH test kit are a must have to make sure that your spa water is healthy. The ideal pH balance of your spa should be hovering around the 7.2-7.8 range. Any lower and your water is too acidic. Any higher and your water is too alkaline/basic. It is important to regularly check pH because any imbalance can hinder the sanitizing agents and promote bacterial growth or cause cloudy or scale buildup in the water. The chemicals needed are pretty straightforward. If your water is too acidic, add an alkalinity increasing agent to lower the pH, and if your water is too alkaline/basic add proper acid agents to raise the pH. Quickspaparts.com offers all the chemical test equipment you need! Chlorine Test Strips Bromine Test Strips Filter Cleaning (Once every two weeks) Once your pH balances are in check, but you are still noticing issues with your water flow and filter efficiency, it may be time to take a look at your filter. A good rule of thumb is to remove and clean your filter bi-weekly to ensure minimal blockages and maximize the life of your filter. A simple cleaning can be done with a soft brush and hose to dig out any large particles and clear the filter for better flow. Filter Deep Clean (~3 Months) A deep filter clean is great to pair with a routine water replacement for your spa. Quarterly, you should drain and refill the water in your hot tub. While you do this it is a good idea to do a thorough cleaning of your filter. Instead of just rinsing the filter out with water, we recommend soaking the filter overnight in cleaning agents to maximize filter health. Always be sure to do a final water rinse and dry of the filter before re-installation. Replacement (Annually) With regular spa use, it is recommended to do a full filter replacement annually. After regular cleaning, the filter media beings to break down over time. Annually a full replacement is recommended to ensure a long life for all other parts of the spa. Nothing can substitute a brand new filter, and it will feel as if your spa has been completely revived. The water will be cleaner and will flow better overall. Buy a new filter at quickspaparts.com today!