Message Troubleshooting

Message Troubleshooting Message Troubleshooting Message Troubleshooting

Control Panel Messages

If you have a message code on the control panel of your spa, such as the one shown at right, follow the steps below.

hh_control_panel.gif

If you have a message code on the control panel of your spa, such as the one shown at right, follow the steps below.

Note: The message troubleshooting shown here applies to Cal Spa control panels built in 2013 and earlier. Beginning with the 2014 product line, Cal Spa control panels display different message codes. For a description of these message codes, see the owner’s manual. 

Control Panel Messages Table

Control Panel Messages
Problem Messages
(Requires action)
Information Messages
(No action required)
Operation Modes Reminder Messages
No message oncontrol panel -- Ecn rPH
dr --- 5LP r5A
dY --F 5td rCL
drY Pr 5bY rt9
HL rdr
HFL rC0
1C rtr
1CE rCH
LF
0H
0H5
HH
OHH
SF
5A
5b
5nA
5nb
5n
5n5

Problem Messages Table

Use the problem message from the "Problem Messages" Column to diagnose problem

Problem Messages
Messages Meaning Action Required
dr Insufficient water detected in heater. Spa will be shut down for 15 minutes. Check water level in spa. Refill if necessary. Make sure pumps are been primed and filter cartridges are clean. Press any button to reset or wait 15 minutes and spa will automatically reset. If message spa does not reset, call customer service.
drY, dY Insufficient water detected in heater. Spa is shut down. (Displays on third occurrence of dr message.) Follow directions for dr message and press any button to reset spa. Spa will not automatically reset when dry or dY is displayed.
HL, HFL A difference in readings between temperature sensors has been detected indicating a possible water flow problem. Make sure spa is filled to proper level and that pumps are primed and filter cartridges are clean. Press any button to reset spa. If message does not reset, call customer service.
1C, 1CE Potential freeze condition detected. No action required. The pumps and the blower will automatically activate regardless of spa status.
LF Persistent low flow problems. Heater is shut down, but other spa functions continue to run normally. Displays on the fifth occurrence of the HL or HFL message within 24 hours. Follow action required for HL or HFL message. Heating capacity of the spa will not reset automatically. Press any button to reset.
OH, OH5 Overheat protection. The spa has shut down. One of the sensors has detected that the spa water is 110°F. warning.gifDO NOT ENTER THE WATER. Remove the spa cover and allow water to cool. At 107°F, the spa should automatically reset. If spa does not reset, shut off the power to the spa and call customer service.
5F Spa is shut down. The sensor that is plugged into the sensor “A” or “B” jack is not working. warning.gifIf the problem persists, call customer service. (May appear temporarily in an overheat situation and disappear when the heater cools.)
5A, 5b, 5nA, 5nb Sensors are out of balance. If this is alternating with the temperature, it may just be a temporary condition. warning.gifIf the display shows only this message (periodically blinking), the spa is shut down. Call customer service.

Information Messages Table

Information Messages
Message Meaning Action Required
1. --
2. ---
1. Water temperature is unknown.
2. Spa is in Economy or Sleep mode.
1. After pump has been running for 2 minutes temperature will be displayed.breadcrumb breadcrumb
2. In Economy or Sleep mode, the pump may be off for hours outside a filter cycle. If you wish to see the current spa temperature, either switch to Standard mode or turn Jets1 on for at least two minutes.
--F Temperature unknown After the pump has been running for 2 minutes, the temperature will be displayed.
Pr When your spa is first actuated, it will go into priming mode. The priming mode will last for up to four minutes and then the spa will begin to heat and maintain the water temperature in the Standard mode.

Operation Modes Table

Operation Modes
Message Operation Mode
Ecn Indicates heater is in Economy Mode
5LP Indicates heater is in Sleep Mode
5td Indicates heater is in Standard Mode
5bY Indicates heater is in Stand-by Mode

Periodic Reminder Messages Table (applies to 9800 system only)

Press the “Mode” button to reset a displayed reminder.

Periodic Reminder Messages
Message Frequency Action Required
rPH Every 7 days Test and adjust pH levels
r5A Every 7 days Test and adjust sanitizer levels
rCL Every 30 days Remove, clean, and reinstall filter
rt9 Every 30 days Test and reset GFCI per manufacturer’s instructions.
rdr Every 90 days Drain and refill spa
rC0 Every 180 days Clean and condition spa cover
rtr Every 180 days Treat wood panels
rCH Once a year Replace the filter

READ MORE AT CALSPASBLOG.COM


Exercise In Your Cal Spas Fitness Swim Spa | A Healthy Habit

Learn what is included in the Cal Spas Exercise Kit and proper ways to connect the kit to your Cal Spas Swim Spa. Learn as much information as you can to make you comfortable and at ease when exercising in your swim spa.

The information below will be helpful when it comes to understanding the Fitness Equipment in a Cal Spas Swim Spa… Check it out!

For 12ft to 14ft spas The exercise kit contains:
• Two hand grips
• Two ankle braces
• Two 6in elastic bands
• Two 18in elastic bands
• Two 25in elastic bands
• Two rowing bars

For 16ft and 17ft spas. The exercise kit contains:
• Two hand grips
• Two ankle braces
• Two 18in elastic bands
• Two 25in elastic bands
• Two 56in elastic bands
• Two rowing bars

Connecting the Exercise Equipment:
The drawings below show different ways the exercise kit can be connected depending on the exercises you wish to do.

Swim Tether:
The swim tether pole has three pieces and assembles easily. Slide the ends of the top and middle sections into the middle and bottom sections. Insert the tether in the anchor hole when you are ready to use it. Buckle the strap around your waist. It is easily adjustable and can accommodate most sizes.

Tru Blue™ Vacuum Safety Break: Cal Spas engineers place the safety of bathers at the highest priority. Our lifesaving Tru Blue™ Vacuum Safety Break feature prevents entrapment by automatically reducing water flow in the event of an obstruction. It’s a unique safety feature that Cal Spas is proud to standard across our entire spa and tub product line.

Air Injection System:
Air venturis are the 1in knobs located around the top of your spa. Each one will let you add a mixture of air with the jet pressure. This is accomplished by rotating the air venturi knob to the left (counterclockwise) to increase the amount of airflow through the jets. To decrease the amount of airflow through the jets, rotate the handle to the right (clockwise). Use the control panel to start and stop the Air Injection System. The JET 1 and JET 2 buttons control the top and bottom jets. Use the air venturi valves to inject air in the water streams for even more power.

Eliminator™ Power Frame Pump: This high-performance pump efficiently circulates and filters your spa’s relaxing waters on low speed while delivering unmatched performance and durability on high speed. It’s just one of the ways Cal Spas delivers both relaxing comfort and tough love to whatever ails you.

Cal Spas Fitness Swim Spas give you the ability to exercise in your own private, welcoming aquatic space. Build muscle, lose weight and be more fit the way passionate swimmers do. Drop excess weight and transform your body into the best shape of your life. Experience post-fitness aquatic recovery that helps your muscles recover faster. Exercise with proper joint support thanks to water buoyancy and enjoy the convenience to work out whenever you want from your patio or backyard. Gain complete freedom from noisy, unsanitary, and crowded gyms. Giving you limitless options to get fit in an entertaining and fun way.